Изогнутое ПП макро волокно для

Elite Concrete Fiber was produced by referring foreign advanced technology for fiber spinning, modified by adding functional additive and special surface-treating. Mixing into cement concrete, it has many advantages such as good dispersing, better water affinity, strong linking force. It is suited to reinforce and crack-resist to every kinds of cement concrete and mortar, specially used in
engineering of building surface, floor, wall etc…..

Concrete with our Macro fiber will have three-dimensional reinforcing with enhanced flexural toughness, impact and abrasion resistance and will also help mitigate the formation of plastic shrinkage cracking in concrete.

Dosage rates will vary depending upon the reinforcing requirements and can range from 2.0 kg/m³ to 6.0 kg/m³.

1, We make the yarn by ourselves and keep inventory. We can delivey in 3-7 days.
2, Capacity 600Ton/Month, 7000Ton/Year Production
3, 70% Export to : Peru, Chile, Ecuador, Costarica, Brazil, Mexico, Australia, Turkey, France, Singapore, Malaysia, Vietnam, Sri Lanka...

These two Fibers have the same advantage and function with Synthetic Fiber Wave. For more detailes pls click the photos as below:

                            Macro Synthetic Fiber (Twist)

                               Macro Synthetic Fiber (Wave)

Monofilament fibers minimize early age cracking in concrete from plastic shrinkage and plastic settlement, while improving its long term durability and impact resistance. For more detailes pls click the photos as below:

  Monofilament polypropylene fiber

Fibrillated polypropylene fiber (mesh)

             Monofilament polyester fiber

       (Bitumen concrete reinforced fiber)

Compared with steel fiber, our fiber has the advantages of anti-corrosion and wear-resistant reducing 50% cost with same volume to steel fiber.
1. Equivalent strengths to WWM and rebar provided by engineering calculations;
2. Controls and mitigates plastic shrinkage cracking and reduces segregation and bleed-water;
3. Provides three-dimensional reinforcement against micro and macro-cracking;
4. Reduces equipment wear, fiber rebound and increases build-up thickness compared to steel fibers for shotcrete applications;
5. Increases overall durability, fatigue resistance and flexural toughness;
6. Reduction of in-place cost versus wire mesh for temperature / shrinkage crack control;
7. Easily added to concrete mixture at any time prior to placement;
8. Tested in accordance with ASTM C 1116, EN14889-2.

Easy to Use

The fibres are wrapped with water-soluble film and uniquely packaged in paper boxes.Just throw the whole boxes of fibres into the concrete mixture, the boxes and film will dissolve within seconds, leaving the fibres to disperse evenly throughout the mixture.

1, Ration design of the fibre concrete:
Generally the recommended amount to add to the concrete is more than 3-6 kg/m³ ( volume ratio is 0.3% ), reinforcement adding amount is 5.5kg/m³ , Compared with adding 47kg of steel fibre, 5.4kg macro synthetic fibre has the same volume ratio to the concrete.
2, Matching Ratio:
Usually, it is no need to Change the matching ratio of the concrete.
3, Mixer Adoption: Double-axle horizontal compelling mixer is priority.
4, Mixing process:
Crushed stones, fibers and sands are put into the mixer in succession. After stirring for two minutes, fiber will fully spread and then add cement and water and stir normally. The addition of materials also can be put into as common concrete, but the stirring time should be properly prolonged to make fiber completely Mixed.
5, Shaping & Maintenance
There is no special requirement, may along the vibrating time for 30s, The maintenance of the fibre concrete should be done same as the normal concrete.

•Slab on Grade and elevated construction (distribution centers, warehouses, etc.)
•Thin walled pre-cast (septic tanks, vaults, walls, etc.)
•Shotcrete for tunnel linings, pool construction and slope stabilization
•Pavements and white-toppings

Q1. What is your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We'll show you the photos of the products and packages
before you pay the balance.

Q2. What is your terms of delivery?
A: EXW, FOB, CFR, CIF, DDU.

Q3. How about your delivery time?
A: Generally, it will take 7 to 15 days after receiving your advance payment. The specific delivery time depends
on the items and the quantity of your order.

Q4. Can you produce according to the samples?
A: Yes, we can produce by your samples or detailed requirement.

Q5. What is your sample policy?
A: We can supply the sample for testing, but the customers have to pay the sample cost and
the courier cost.

Q6. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery

Q7: How do you make our business long-term and good relationship?
1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.

Pls feel free to contact us  at Anytime:
Ms. Helen Chu
Mobile & WhatsApp: +86 18668055321
Skype: helenyuan413; QQ: 413367414
E-mail: helen(AT)elite-indus.com