Форма для отверждения комнатной температуры Hanast силиконовая резина жидкий силикон смолы игрушек поделок осветительное приспособление формы
- Категории: Rubber Raw Materials >>>
- Поставщик: Shenzhen,Ha,Nai,Si,Te,Technology,Co.,Ltd.
Поделиться:
Описание и отзывы
Характеристики
Hanast Room Temperature Curing Mold Silicone Rubber Liquid Silicone For Resin Toys Craft Light Fixture Molds Making
Product Description
Hanast Liquid Silicone Rubber For Mold Making | ||||||||||
Appearence | Semi-Transparent / Milk white | |||||||||
Specific Gravity (g/cm3) | 1.05 | 1.05 | 1.13 | 1.14 | 1.14 | |||||
Hardness Shore A | 10 | 15 | 25 | 30 | 35 | |||||
Mixing Ratio (A:B) | 100:2 | 100:2 | 100:2 | 100:2 | 100:2 | |||||
Viscosity (mPa.s) | 25000±2000 | 25000±2000 | 25000±2000 | 25000±2000 | 25000±2000 | |||||
Operating Time (min) | 20-40 | 20-40 | 20-40 | 20-40 | 20-40 | |||||
Vulcanization Time | 3-5h (25℃) 20-30min (60℃) | |||||||||
Shrink Rate (%) | <0.1 | |||||||||
Tensile Strength (Mpa) | 3.2 | 3.2 | 3.2 | 3.2 | 3.2 | |||||
Elongation (%) | 460 | 460 | 460 | 460 | 460 | |||||
Tear Strength (kN/m) | 20±5 | 20±5 | 20±5 | 20±5 | 20±5 | |||||
Product Characteristics:
◆ It can perfectly replicate the small lines and patterns of the product, which is suitable for mass production and replication of cement products.
◆ Silicone mold can be reused, saving production costs.
Storage:
Sealed storage between 23±2℃ away from heat, light.
1. Good fluidity, fine and smooth colloid, no impurities;
2. There are many times of mold turning, which is suitable for mass production and replication of gypsum cement products;
3. High tear strength, good tensile force, and long service life of silicone mold;
4. High temperature resistance, no expansion, no deformation of the mold;
5. Low shrinkage (≤0.1%), can be quickly cured at room temperature.
2. There are many times of mold turning, which is suitable for mass production and replication of gypsum cement products;
3. High tear strength, good tensile force, and long service life of silicone mold;
4. High temperature resistance, no expansion, no deformation of the mold;
5. Low shrinkage (≤0.1%), can be quickly cured at room temperature.
* Performance can be adjusted according to customer requirements.
Product Application:
◆Mold making liquid silicone rubber is suitable for gypsum handicrafts, gypsum lines, cement components, cement rockeries, cement sculptures, background walls, sandstone carvings and other products to replicate and make silicone molds.
◆ It can perfectly replicate the small lines and patterns of the product, which is suitable for mass production and replication of cement products.
◆ Silicone mold can be reused, saving production costs.
Operating Process:
1. Clean the surface of the product, apply a layer of release agent evenly, and fix the product on a flat wooden or glass plate;
2. Cut the wood plate, surround the product (leave a distance of about 5mm between the board and the product, and apply a mold release agent), and seal the gaps on the four sides with a hot melt glue gun;
3. According to the size of the product, the complexity of the structure and the use of weighing silica gel for proportioning, after fully mixing and stirring, pour a part into the mold, and then vacuum together;
4. After vacuuming, pour all the remaining silica gel into the mold;
5. After the silicone is completely cured (3-4 hours), remove the cardboard, remove the silicone mold, and trim the excess silicone on the four sides with scissors;
6. Carry out demoulding, take out the mold, and trim the edges;
7. At this point, the whole process is over, and it can be put into production after 24 hours. Store the silicone mold in a ventilated, cool and dry place.
Packing:
25KG/200KG/barrel
Storage:
Sealed storage between 23±2℃ away from heat, light.
The service life is 12 months.
Precautions:
1. The amount of curing agent added should depend on the temperature, when the temperature is high, it will be reduced. Adding too much curing agent will affect the quality of the mold, and the silicone mold will become brittle; adding less curing agent will prolong the curing time;
2. It is enough to vacuum to -0.1mpa. The vacuuming time should not be too long to prevent the cross-linking reaction of the silica gel during vacuuming, so that the silica gel becomes piece by piece, resulting in waste of raw materials;
1. The amount of curing agent added should depend on the temperature, when the temperature is high, it will be reduced. Adding too much curing agent will affect the quality of the mold, and the silicone mold will become brittle; adding less curing agent will prolong the curing time;
2. It is enough to vacuum to -0.1mpa. The vacuuming time should not be too long to prevent the cross-linking reaction of the silica gel during vacuuming, so that the silica gel becomes piece by piece, resulting in waste of raw materials;
Best Selling
Company Profile
Shenzhen Hanast Technology Co, Ltd. was established on 2019. The factory is located in Sanming City, Fujian Province, covering an area of 20,000 square meters.
Hanast is a silicone raw material company integrating R&D, production and sales, mainly engaged in conventional silicone rubber,special silicone rubber, RTV adhesive sealant, two-component electronic potting adhesive, thermally conductive silicone, thermally conductive silicone grease, lubricating silicone grease, damping silicone grease, platinum vulcanizing agent and other silicone raw materials.
The products comply with ROHS standard, obtain SGS, Food Grade Certification, and the enterprise passed ISO9001. 2015 certification. Our products have obtained many national invention patents and utility model patents, and are widely used in silicone kitchenware, high temperature wire and cable, industrial silicon rollers, medical industry, baby products, sporting goods, adult products, new energy vehicles and other fields.
Certifications
Our Services
Free Samples & After-Sales Service
We can offer new customers free samples for testing & Free technical supporting.
We can offer new customers free samples for testing & Free technical supporting.
Due to the time difference and holidays, we will offer solutions within 24 hours, After-sale service 7*24h!
Our Factory
Packing & Shipping
FAQ
Q1 : Could you offer liquid silicone rubber samples for testing first?
Q3 : What is payment term?
A : Yes, we can offer 1KG of liquid silicone rubber sample for free. Please come and try quickly.
Q2 : What is the lead time of the silicone rubber materials samples?
A : Normally within 3-4 days.
Q3 : What is payment term?
A : Western Union, Paypal, T/T, L/C at sight, Alipay.
Q4 : Are the materials you use all safe?
A : Yes, for sure. We guarantee that we use safe materials with Food Grade, Non-toxic and Free-phthalate. We are original manufacturer with 7 years of experience, don't worry about this.
Q5 : Could you offer us certificates for verification?
A : Yes, we can. We can also assist you to do the certificate verification.
Q6 : Are you a direct silicone rubber manufacturer?
A : Yes, we are an experienced manufacturer specializing in various silicone rubbers and adhesive for more than 7 years.
Contact us freely if any questions.
Похожие товары
Жидкий силиконовый каучук RTV для литья бетонного продукта
US $4.50-$8.00
EPDM 4570 гранулы этиленпропиленовой резины EPDM для продажи
US $2.10-$2.80
Премиум качество белый жидкий латекс nbr для пропитанных продуктов
US $850.00-$950.00
Силиконовая приманка для мягких приманок
US $0.75-$1.05
Новинки - Розница
