XTA DP548 Многофункциональный процессор аудио Pro цифровой динамик

TA dp548, dp544 5 series dynamic audio manager The 5-series dynamic management function is not only the sum of its various parts,
but also has the function of 4-series products, adds the function equivalent to four D2 dynamic equalizers at the input, adds C2
compression channel at each output, and adds a new matrix hybrid function mode. By using two units (dp548 – 4 I / 8 output, and
dp544 – 4 I / 4 output), you can use the updated DSP platform to retain and expand all the original functions and sound quality of
the 4 series, which has never been before. Seeing the breakthrough features of audiocore, all these bring new dynamic combinations
Two 5 series units are available: Dp548 – 4 inputs 8 outputs Dp544 – 4 inputs and 4 outputs Each input has a 28 band graphic
equalizer that can be configured to model our own gq600 or older inductor based designs (e.g. dn27). There are also eight
"traditional" parameter equalizers on each input. All parameter parts can be reconfigured for many alternative filter
characteristics, including familiar high and low-grade and notch filters, but band-pass, elliptical and variable "Q" shapes and
phase adjustment can be in steps of 2 degrees. Importantly, you may be used to this equalizer, a powerful dynamic equalizer. The
three frequency bands of SIDD's dynamic EQ are available for each input and support all four operating modes (therefore, cut-off /
enhancement above or below the threshold). Each frequency band will cover the entire range of 20-20K, with envelope (attack /
release) control and setting the "strength" (dynamic ratio) that allows the gain adjustment amount and selects the effect. Dynamic
equalizer, graphic equalizer settings, all other input settings or all output settings and, if necessary, each combination of
these settings can also be stored in its own memory. Considering that this can be daunting and can still be edited through the
front panel, audiocore turns on dynamic EQ editing in a very intuitive way. Routing input to output is as flexible as before, any
input or combination of inputs can switch to any output, and there are various useful templates to help you get started (and
default intersections to help). The 5 series also supports the full matrix hybrid mode, in which the input can be mixed with any
output in any proportion, and four "sends" are provided on each output channel, not just on / off. From the output part, the slope
of the necessary frequency division filter ranges from 6dB / octave to 48dB / octave. Following more than nine parametric
equalizer bands, we can then choose a dynamics useful for protection or creative use. Before the limiter part, there is now a
functional compressor with variable knees, which can change it from a safe corrective tool (with hard knees) to a soft (but still
high ratio if necessary) effect. Its existence is gradually felt only with the increase of the threshold. Approach and surpass.
Each output also has a limiter combination - a limiter designed to prevent overheating of a single drive, and an additional lead
"D-max" limiter to increase safety and prevent excessive drive movement. With a completely flexible combination of all channels
for time alignment, coupled with sub millimeter accuracy, it can be seen that the 5 series will be applicable in any case. input
Electronic balance (optional transformer) AES / EBU (optional), fully installed in all 5 Series Units Impedance > 10K ohm CMRR>
65dB 50Hz – 10kHz output All electronic balance (optional transformer) AES / EBU standard for all 5 Series Units Source imp <
60ohms Small load 600ohm Level + 20dbm to 600ohm load sampling rate dp548 – internal 96KHz, can accept and convert 192Khz.
Frequency response ± 0.5dB 10Hz – 32kHz Dynamic range > 116dB 20Hz - 20kHz. Unwtd Distortion < 0.001% gt; Delay 650 Ms. (in steps
of 0.325 μ s) The output gain can be adjusted and muted in the range of + 15dB to - 40dB in 0.1 dB steps equilibrium Filter
parameters - 8 per input / 9 per output Figure of 28 frequency bands on each input of additional filter Each parameter can be
switched to bandpass, all pass, notch, variq, expansion frame and elliptical response Phase filtering – 2 degree steps per input
and output Frequency division filter Bessel / Butterworth per octave 6 / 12 / 18 / 24 / 48dB and linkwitz Riley 12 / 24 / 48dB per
octave Dynamic EQ 3 frequency bands per input Parameter behavior – 19.7hz – 32kHz & 39; Q&＃39; 0.4 –128， Gain automatic gain
adjustment 18db Ratio (switching in the above mode) 4:1 Ratio (in all other modes) 2:1 Attack 70us – 2.0 seconds Release 11ms –
3.4 seconds compressor One per output Scale 16:1 Variable inflection point – 12 steps + off (hard) Attack 70us – 2.0 seconds
Release 11ms – 3.4 seconds Mixed matrix mode Input in steps of 0.1dB from - 40.0db to_ 15.0db continuously and variably sent to
each output, plus off. limiter Threshold + 22dbu to - 10dbu Attack time 0.3 to 90 milliseconds The release time is 4, 8, 16, or 32
times the attack time Clip / D-max limiter Forward looking attack time, fast, medium or slow release time Connector Input 3-pin
female XLR Output 3-pin male XLR RS485 I / O XLR RS232 9-pin (female) D connector Power Supply 3-pin IEC Power supply 60vac –
240VAC Power consumption < 40W Weight 3.5kg. Net weight (5kg. Freight) Dimensions 1.75 inches (1U) x 19 inches x 12 inches (44 x
482 x 305 mm), excluding connectors.