ArcFeeder IV с датчиком напряжения проволочный Фидер

The voltage-sensing wire feeder uses the welding voltage to generate the energy required for controlling the wire feeder's operation. Before welding, you just select the desired settings for the feeder and the power source according to the welding requirements, the base materials, filler materials, and the shielding gas.

When you start welding in CC, parameters can be controlled by the feeder in order to ensure the high welding quality.

For normal MIG/MAG welding, the parameters' values are controlled by the power source via the control cable, but voltage-sensing technology makes such a control cable between the power source and the feeder unnecessary.

Constant Current (CC) power source
The CC type of welding machine can change the wire feeding speed according to the arc voltage.
The voltage will change with different arc lengths but with slight change for current.
Constant Voltage (CV) power source
The CV type of welding machine can maintain a relatively stable, consistent voltage regardless of the change for current. It results in a relatively flat volt-amp curve. The MIG/MAG welding machines are typically CV type machines.

- Voltage sensing technical wire feeder;
- Fully-enclosed molded composite metal-plastic case;
- Easy operation, easy connection with power source;
- Capable of Flux cord, Solid wire and Inner-shielded wire welding;
- No need special control cable between the power source and wire feeder;
- Suitable for CC/CV power source;
- 4-roll print motor with PWM drive;
- Excellent arc ignition
- Good reliability
- Automatically suit the change of welding polarity.
- Suitable for most DC power source
- Scale/Digital Meter/LCD show parameter separately

● Sort of base metal:Various steel.
● Thickness of base metal:≥ 2mm
● Wire diameter(mm):Flux-cored welding wire Ф1.2~Ф2.0 or max. 2.4mm
                                         Innershield welding wire Ф1.6~Ф2.0 or max. 2.4mm
                                          Solid welding wire Ф1.0~Ф1.6mm

- ArcFeeder 1 Unit
- Arc Voltage Sensing Lines\t1 Piece (3m with sampling clamp)

1. Welding torch
2. Cable

ArcFeeder System Connection Diagram:

AreFeeder Sketch:

1. TORCH SOCKET:EURO style(standard outfit) PANASONIC OR other.(optional )
2. VSLEAD:voltage sensing lead,used for connecting voltage sensing cable.
3. WFS (Wire feeding speed): Used for adjusting welding wire speed, corresponding to welding current, wire diameter and welding materials.
4. WFS display:used for wire feeding speed display,unit:mpm.
5. POLARITY indicator:When DCEN is valuable, POLARITY indicator is lighting.
6. POWER indicator:When power is on, POWER indicator is lighting.
7. WELDING CONNECTOR:used for connecting welding cable.
8. Inlet: Used for connect shielded gas tube.
9. Purge: Used to test the shielding gas and measure the gas flow. If presses down this switch, there is no electricity in wire.
10. GAS regulator:used for protection gas regulating,unit:LPM.
11. TORCH HOLD:used for torchhold selection,when "1",torchhold is valuable.
12. POWER switch: Used for turning ON/OFF the power in wire feeder. Please turn OFF the feeder when it is not in use.
13. CC/CV selection mode: Used for selecting working mode of wire feeder. Set this switch according to the power source you are using.
14. Inch: Used to drive the welding wire before welding. If presses it down, there is also no electricity in wire.

Welding of vehicle axle by matching KR350, achieving low spatter and high-speed welding; welding conditions: φ1.2 solid wire, mixed gas(Ar80%+CO220%) and 260A~280A/30~32V; welding speed: 1.5m/min:

Welding of pressure vessels by matching common MMA; welding conditions: φ1.2 solid wire, mixed gas (Ar80%+CO220%) and 260A~280A/30~32V:

Related Products:

ArcNova300

ArcNova500

ArcFeeder

ArcFeeder I

ArcFeeder III

AutoTIG