PU110 черное полиуретановое покрытие для кровли водостойкое жидкое

Описание и отзывы

Характеристики

PU110 black polyurethane  roof paint coating waterproofing waterproof  liquid rubber coating 

 

 

SEPNA PU110 is one component self lelveling polyurethane based coating that cures by reaction with atmospheric moisture to form a seamless but flexible waterproofing membrane.

 

 

Key Features

-Single component, convenient to apply
-High cohesive force and ductility.
-Resistance to chemical corrosion, low temperature.
-Anti-aging performance better than cement based polymer sealant

-Low voc, eco-friendly

 

Typical Applications

 

-Bathroom floor, kitchen floor, balcony, etc.

-Concrete floors to stop water leaking as waterproof layer..

- Interior bathroom, toilet floor, basement.

 

Technical Data Table

PROPERTY	STANDARD/UNITS	VALUE
Appearance	-----	liquid
Color	Visual inspection	Black/ grey/white  (color can be adjusted according to large amount)
Density	g/m3	1.35±0.1
Surface dry  time	hour	≤3
Solid Content	%	≥90
Sagging property	mm	Self-leveling
Strength at break	Mpa	>2.5
Elongation at break	%	>500
Curing speed	mm/24h	3 ~ 5
Application Tetemperature	°C	5-35
Service	°C	-40~+80
Shelf life	month	6

 

 

Direction of Use

 

 Tools preparation: clean tools including saw toothed plastic scraper, brush ,plastic drum, 30kg electronic scale,rubber gloves and shovel knife.

 Application environment requirement: sealant should be installed in the cleaning condition at  5~35°C relative humidity 35~85%RH.

Cleaning substrates surface:substrate should be solid without loose materials; dry without construction on the wet substrates; clean without dust ,oil,asphalt,tar,paint,wax,rust,Non-Permeable agent,curing agent,release agent and film etc. It should be cleaned by wiping out,cutting,polishing,

sweeping,washing,scrubbing and blowing.

 If large cracks on the substrate surface,the cracks should be filled by sealant ,and filled surface should be scraped as the same level as coating. After surface curing depth reach up to more than 3mm, the coating can be appiled on the joints.

The first coating application: first ,brush the wall corner and pipe joints partly ,then using saw toothed plastic scraper to knife-coating in large area. It should require homogeneous without too thick, the thickness of layer should be 0.5mm in general(If too thick, coating layer is easy to emerge bubbles ).

The second coating application: after the fully curing of the first coating layer (about 12 hours),

then knife-coating homogeneously at the second time. The good thickness of the second coating is 0.7mm.The direction of knife-coating should be vertical with the first direction of knife-coating. Please refer to the first coating application in details.

 The third coating application: after the fully curing of the second coating layer,then knife-coating homogeneously at the third time.The direction of knife-coating should be vertical with the second direction of knife-coating. Special instruction: the the times of knife-coating should be confirmed based on thickness design of coating, the total coating thickness is 2.0-2.2mm.

Protective layer construction: if needed, protective layer can be applied on the surface of coating layer.

Cleaning tools: dip the tools in methylbenzene or dimethylbenzene(prohibit it strictly to dip in ethyl alcohol solvent), the tools can be used after cleaning the solvent. If long time not be used , it should be washed by alcohol or other organic solvent. The cured sealant should be scraped and teared off.

 

Packaging & Shipping

 

Coat film thickness is 1.00mm, usage is 1.3kg per square meter

Packing: 5kg metal bucket, 20kg metal bucket

 

 

Our Services

 

 

FAQ

Q: May I know more about your company?

A: Sure! Suzhou Sepna is only one China manufacturer supplying self leveling polyurethane joint sealant.We mainly focus on researching of one component polyurethane joint sealant and one component polyurethane coating for large construction projects. 

Q: What's your delivery time?

A:  Normally, the delivery time of sample order is 3-7days 

      Bulk order is 10 days after received the PO and deposit

Q: Can I get samples?

A: YES! 1000g tin free sample supplied for your quality check.

 Three ways to get free samples below

 1. Supply us your import express account DHL/Fedex for sample shipping

 2. You can inform your DHL/Fedex to pick up the sample from Sepna factory.

 3. Pay  express fee to Sepna company by Paypal or TT, we will arrange the sample delivery on our side.

 

Q: What is your MOQ?

A:  Our MOQ is 1000kg for black color , 5000kg for grey color, 10000kg for customized color 

 

Q: Can you do OEM lable for the products?

A: YES, the OEM service such as buyer labels are accepted as long as your order reach our standard amount.

 

Any more questions, please contact us anytime!